If your Canon PIXMA TS6320 keeps turning on and off repeatedly, you're dealing with a frustrating power cycling issue that prevents any printing, scanning, or copying. This problem—where the printer boots up, displays the Canon logo, then shuts down and restarts in an endless loop—typically stems from power supply problems, internal hardware faults, or firmware corruption. The PIXMA TS6320, a popular all-in-one wireless inkjet printer released in 2019, can develop this issue after power surges, failed updates, or component wear. This printer repair guide walks you through proven troubleshooting steps to fix printer instability and restore normal operation.
Common Causes of Canon PIXMA TS6320 Power Cycling
Understanding why your printer keeps restarting helps target the right fix. The TS6320's compact power board and USB-C power input design make it susceptible to certain failures. Most power cycling cases trace back to the power adapter, the internal power supply board, or corrupted firmware that prevents the boot process from completing. External factors like overloaded circuits, damaged cables, or incompatible third-party power supplies also trigger this loop. Before assuming hardware failure, systematic troubleshooting can isolate whether you need simple printer support or professional service.
Step-by-Step Troubleshooting to Stop the Restart Loop
1
Inspect the Power Adapter and Cable: The Canon PIXMA TS6320 uses a specific AC adapter (model K30353 or equivalent, 24V output). Examine the entire length of the power cord for fraying, kinks, or chew marks. Check that the USB-C connector at the printer end seats fully and isn't wobbly. Try a different wall outlet on a different circuit—avoid power strips and surge protectors for this test. If you have access to a multimeter, verify the adapter outputs approximately 24V DC. A failing adapter that drops voltage under load causes intermittent power cycling.
2
Perform a Hard Reset: Unplug the power cord from both the wall and printer. Press and hold the power button on the TS6320 for 60 seconds to discharge residual power from the capacitors. Leave the printer unplugged for at least 15 minutes. This extended drain period clears temporary firmware glitches that cause boot loops. Reconnect power directly to a known-good wall outlet, then press power once. If the printer completes boot normally, the issue was likely a firmware hang rather than hardware damage.
3
Remove All Peripherals and Consumables: Open the scanner lid and document cover, then power cycle with these open to reduce mechanical load during startup. Remove both ink cartridges (CLI-281 series) and the paper tray entirely. Disconnect any USB cables or Ethernet connections. A shorted cartridge chip, jammed purge unit, or faulty paper sensor can trigger protective shutdowns. Attempt to boot with minimal components—if successful, reintroduce items one at a time to identify the culprit.
4
Check for Firmware Corruption and Update: If the TS6320 powers on briefly enough to show menus before restarting, access the settings screen during the brief operational window. Navigate to Device Settings > Firmware Update. Alternatively, download the latest firmware from Canon's support site using your computer, then apply via USB connection during a stable boot window. Firmware version 2.000 or later addressed several boot stability issues. If the printer cannot stay on long enough, proceed to recovery mode: hold Stop + Power simultaneously for 10 seconds, then connect via USB to attempt emergency reflashing.
5
Inspect Internal Power Supply Components: If comfortable with electronics repair, remove the five screws securing the bottom panel and carefully detach the scanner assembly ribbon cable. Locate the power supply board near the USB-C input—look for bulging electrolytic capacitors, burned traces, or brown discoloration. The TS6320 uses susceptible 1000µF/16V capacitors that fail after 3-4 years. Replace with equivalent low-ESR capacitors rated 105°C. Also check the F2 fuse near the power jack; a blown fuse indicates deeper circuit damage requiring professional printer repair.
6
Test with Known-Good Power Source and Evaluate Repair Cost: Borrow an identical Canon power adapter if possible, or purchase a verified OEM replacement (part CA-CP200 compatible). If the printer cycles with a confirmed-good adapter, the internal power board or main logic board has failed. At this point, weigh repair costs against replacement—the TS6320's current value often makes professional board-level repair uneconomical unless covered under warranty or Canon's extended service plan. For units under one year old, contact Canon directly for warranty printer support.
⚠️ Important: Never attempt to power your Canon PIXMA TS6320 with a non-Canon power adapter, even if the voltage and connector match. Third-party adapters frequently lack proper voltage regulation and surge protection, which can permanently damage the printer's logic board and void your warranty. Additionally, capacitor replacement involves exposure to high-voltage retained charge—discharge all capacitors with an insulated screwdriver before touching any components, or seek qualified tech support.
Frequently Asked Questions
Why does my Canon PIXMA TS6320 keep restarting when I try to print?
The additional power draw from activating the print head and carriage motor can trigger shutdown if your power adapter is failing or the internal power supply cannot maintain stable voltage under load. Test with a new OEM adapter first, then inspect for mechanical obstructions in the print path that cause motor overload.
Can a power surge cause permanent damage that leads to power cycling?
Yes, power surges commonly damage the TS6320's power supply board and can corrupt firmware stored in flash memory. Even with a surge protector, fast transients may pass through. After any surge event, the printer may boot-loop due to partial firmware corruption or blown protection components on the power board.
How do I know if my PIXMA TS6320 needs repair or replacement?
If troubleshooting through adapter replacement, hard resets, and component isolation doesn't resolve the Canon PIXMA TS6320 power cycling, and the unit is out of warranty, compare repair estimates to replacement cost. As of 2024, professional diagnosis and board replacement typically exceeds $150—often approaching the cost of a new comparable printer. For printers over three years old with heavy use, replacement is usually the practical choice.
Still Need Help With Your Canon Printer?
If these troubleshooting steps didn't resolve the issue, our certified Canon printer technicians are standing by. Get expert support in minutes.